{"title":"Victron Energy | Battery Management Systems","description":"","products":[{"product_id":"victron-energy-ve-bus-bms-v2-battery-management-system-1041820","title":"VICTRON ENERGY | VE.Bus BMS V2 Battery Management System (1041820)","description":"\u003ch2\u003eDescription\u003c\/h2\u003e\n\u003cp\u003e\u003cb\u003eThe next generation VE.Bus BMS V2\u003c\/b\u003e\u003cbr\u003e\u003cspan\u003eThe VE.Bus BMS V2 is the next generation of the VE.Bus Battery Management System (BMS) for Victron Energy Lithium Battery Smart batteries. These batteries are Lithium Iron Phosphate (LiFePO4) batteries and are available in 12.8 V or 25.6 V in various capacities. They can be connected in series, parallel and series\/parallel so that a battery bank can be built for system voltages of 12 V, 24 V or 48 V. The maximum number of batteries in one system is 20, which results in a maximum energy storage of 84 kWh in a 12 V system and up to 102 kWh in a 24 V1) and 48 V1) system.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eIt is designed to interface with and protect the lithium batteries in systems that have Victron inverters or inverter\/chargers that have VE.Bus communication.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cb\u003eProtects each individual cell of a Victron Lithium Battery Smart\u003c\/b\u003e\u003cbr\u003e\u003cspan\u003eFor reliable and safe operation, a LiFePO4 battery must be monitored and protected against over voltage and under voltage of any individual cell, and also over temperature or under temperature conditions. The Victron Lithium Battery Smart range includes integrated cell voltage monitoring, cell voltage balancing, and temperature monitoring. If the cell voltage or battery temperature is outside of the allowable range, this is communicated to the BMS via two BMS cables with M8 circular connectors. In systems with multiple batteries, the BMS cables of each battery are connected in series (daisy chained), with the first and the last BMS cables connected to the BMS.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eBased on the status of the Victron Lithium Battery Smart or batteries, the BMS will:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Generate a pre-alarm signal to alert of an imminent cell under voltage condition.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Disable inverting in VE.Bus inverters or inverter\/chargers via VE.Bus, and disable other loads via the “Load Disconnect” terminal in the event of a cell under voltage condition.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Disable charging in VE.Bus inverters or inverter\/chargers via VE.Bus, disable VE.Direct and VE.Can solar chargers via a GX device and disable other chargers via the 'Charge Disconnect' terminal in the event of a cell overvoltage, under temperature or over temperature condition.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cb\u003eCommunication with VE.Bus products\u003c\/b\u003e\u003cbr\u003e\u003cspan\u003eMultiPlus, Quattro or Phoenix inverters connect to the ‘MultiPlus\/Quattro’ port with a standard RJ45 UTP cable. The BMS disables inverting in the case of a cell under voltage condition and disables charging in the case of a cell over voltage or temperature condition.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cb\u003eCommunication with remote devices\u003c\/b\u003e\u003cbr\u003e\u003cspan\u003eA GX device (such as a Cerbo GX), Digital Multi Control (DMC) panel or a VE.Bus Smart dongle (including any combination) can be connected to the BMS via the 'Remote panel' port. These accessories can all be used in combination with the BMS to remotely control the VE.Bus Inverter or inverter\/charger switch state (on\/off\/charger-only).\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cb\u003eAuxiliary power input and output terminals\u003c\/b\u003e\u003cbr\u003e\u003cspan\u003eThe BMS has a dedicated power output terminal (GX-Power) for a GX device and an auxiliary power input terminal (Aux-In) for an external DC power source, such as an AC\/DC adaptor. In the event of a system shutdown, the GX device will remain powered via the auxiliary power input or be disconnected to prevent further battery discharge.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cb\u003eRemote terminals\u003c\/b\u003e\u003cbr\u003e\u003cspan\u003eThese terminals can be used to switch the BMS on or off. When the BMS is off, both outputs will be free floating so that loads and chargers are turned off. There are two remote terminals, namely, “Remote L” and “Remote H”. A remote on\/off switch or relay contact can be connected between L and H to switch the BMS on or off. Alternatively, terminal H can be switched to battery plus, or terminal L can be switched to battery Minus.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cb\u003eLED indicators\u003c\/b\u003e\u003cbr\u003e\u003cspan\u003eThe BMS has the following LED indications:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Status (blue): Lights shortly once every 10 seconds to indicate normal operation.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Temp or Cell\u0026gt;4 V (red): Lights when the charge disconnect output is low because of cell overvoltage or overtemperature.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Cell\u0026gt;2.8 V (blue): Lights when the load disconnect output is high and the battery cell voltages are above 2.8 V.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2\u003e\u003cspan\u003eSpecifications\u003c\/span\u003e\u003c\/h2\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eCurrent Draw - Regular Operation\u003c\/div\u003e\n\u003cdiv class=\"fsProductSpecifications__value\"\u003e10 mA (excluding Load disconnect current)\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eInput Voltage Range\u003c\/div\u003e\n\u003cdiv class=\"fsProductSpecifications__value\"\u003e9 – 70 VDC\u003cbr\u003e\u003cbr\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"fsProductSpecifications__value\"\u003e(\u003cspan\u003e1041820)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":51035166965924,"sku":"1041820","price":156.4,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0423\/0820\/6756\/files\/Screenshot_56_9a49436e-1427-45ca-a7a1-0eb2585aa87c.png?v=1750373725"},{"product_id":"victron-energy-lynx-smart-bms-500-m10-1043612","title":"VICTRON ENERGY | Lynx Smart BMS 500 - M10 (1043612)","description":"\u003ch2\u003eDescription\u003c\/h2\u003e\n\u003cul class=\"fs-list--cleaner\"\u003e\n\u003cli class=\"ng-star-inserted\"\u003e500A or 1000A contactor\u003c\/li\u003e\n\u003cli class=\"ng-star-inserted\"\u003eBluetooth enabled\u003c\/li\u003e\n\u003cli class=\"ng-star-inserted\"\u003eFor Victron Lith. NG batteries\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003eThe Lynx Smart BMS NG is an exclusive Battery Management System (BMS) specially crafted for the Victron Lithium NG batteries. These batteries utilize Lithium Iron Phosphate (LiFePO4) technology and are offered in 12.8 V, 25.6 V, and 51.2 V versions with different capacities. They can be arranged in series, parallel, and series\/parallel configurations, allowing the formation of battery banks with system voltages of 12V, 24V, or 48V. The maximum number of batteries in a single system is 50, providing a maximum energy storage of 192kWh in a 12V system and up to 384kWh in a 24V and 48V system. For detailed information regarding these batteries, please visit the Victron Lithium NG battery product page. Out of the various BMSes available for the all new Lithium NG batteries, the Lynx Smart BMS NG is the most feature-rich and complete option and integrates seamlessly with other M10 products in the Lynx Distributor system. It is available in 500 A (M10) and 1000 A (M10) versions 1)\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2\u003e\u003cspan\u003eFeatures\u003c\/span\u003e\u003c\/h2\u003e\n\u003cp\u003e\u003cspan\u003e\u003cb\u003eBuilt-in 500 A or 1000 A contactor\u003c\/b\u003e\u003cbr\u003e• Available in 500 A (M10) and 1000 A (M10) versions.\u003cbr\u003e• Acts as a secondary safety system to protect the battery in case primary controls (ATC, ATD and\/or DVCC) fail.\u003cbr\u003e• Suitable as a remote controllable main system switch.\u003cbr\u003e\u003cbr\u003e\u003cb\u003ePre-charge circuit\u003c\/b\u003e\u003cbr\u003e• Prevents high inrush currents when connecting capacitive loads like inverters.\u003cbr\u003e• Eliminates the need for external pre-charging devices.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eMonitoring and control\u003c\/b\u003e\u003cbr\u003e• Bluetooth connectivity for monitoring and control via the VictronConnect App or VE.Can connectivity in combination with GX devices such as the Cerbo GX or Ekrano GX and the VRM portal.\u003cbr\u003e• Readout of cell voltages and temperatures also on GX devices and the VRM portal.\u003cbr\u003e• Built-in battery monitor provides data such as state of charge, voltage, current, historical data, status info and more in real time.\u003cbr\u003e• Diagnostic at a glance with Instant Readout\u003cbr\u003e\u003cbr\u003e\u003cb\u003eDVCC closed loop control as well as ATC\/ATD contacts\u003c\/b\u003e\u003cbr\u003e• Compatible Victron inverter\/chargers, the Orion XS 12\/12-50A DC-DC battery charger and solar charge controllers are automatically controlled via a connected GX device and DVCC.\u003cbr\u003e• ATC\/ATD contacts can be used to control other chargers and loads that have a remote on\/off port.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eProgrammable relay\u003c\/b\u003e\u003cbr\u003e• Can be used either as an alarm relay (combined with the pre-alarm) or to control an alternator via its external regulator (ignition cable).\u003cbr\u003e• Features Alternator ATC mode for safe alternator disconnection before battery disconnects\u003cbr\u003e\u003cbr\u003e\u003cb\u003eAUX terminal\u003c\/b\u003e\u003cbr\u003e• Onboard auxiliary power supply (1.1 A @ system voltage) for powering specific loads (i.e. a GX device) post-BMS shutdown.\u003cbr\u003e• Automatic shutdown of BMS and AUX connection if no charge voltage detected within 5 minutes after a low voltage event\u003cbr\u003e\u003cbr\u003e\u003cb\u003eVE.Can and NMEA 2000 data communication\u003c\/b\u003e\u003cbr\u003e• Easy connection and communication with GX devices via VE.Can using a standard RJ45 network cable.\u003cbr\u003e• Integration into marine networks via NMEA 2000 protocol (requires a VE.Can to NMEA 2000 micro-C male cable).\u003cbr\u003e\u003cbr\u003e\u003cb\u003eLynx Distributor fuse monitoring\u003c\/b\u003e\u003cbr\u003e• Monitor fuse status of up to 4 connected Lynx Distributors via VictronConnect or GX devices.\u003cbr\u003e• Receive alarms in case of blown fuses.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2 class=\"pb-1 pb-md-4 fs-heading-separator\"\u003eSpecifications\u003c\/h2\u003e\n\u003cdiv class=\"fsProductSpecifications__table col-12 col-md-8 pb-3 pb-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"row\"\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003e\n\u003cul\u003e\n\u003cli\u003eBusbar: M10 (Torque: 33 Nm)\u003c\/li\u003e\n\u003cli\u003eContinuous Current Rating: \u003cspan style=\"font-size: 0.875rem;\"\u003e500A\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eFuse: \u003cspan style=\"font-size: 0.875rem;\"\u003eM10\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eModel: \u003cspan style=\"font-size: 0.875rem;\"\u003eBMS 500 A NG\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eSize: \u003cspan style=\"font-size: 0.875rem;\"\u003e7.5\"H x 7.1\"W x 3.1\"D\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eVolts: \u003cspan style=\"font-size: 0.875rem;\"\u003e9-60V DC\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eBarcodes: \u003cspan style=\"font-size: 0.875rem;\"\u003e190760635519, \u003c\/span\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e8719076063551, \u003c\/span\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eLYN034160310\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e\u003cspan\u003e(1043612)\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":51127895523492,"sku":"1043612","price":884.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0423\/0820\/6756\/files\/1_db240b09-8896-4f13-8c9f-8cdaeee4c42d.webp?v=1757643585"},{"product_id":"victron-energy-lynx-smart-bms-1000-m10-1044416","title":"VICTRON ENERGY | Lynx Smart BMS 1000 - M10 (1044416)","description":"\u003ch2\u003eDescription\u003c\/h2\u003e\n\u003cul class=\"fs-list--cleaner\"\u003e\n\u003cli class=\"ng-star-inserted\"\u003e500A or 1000A contactor\u003c\/li\u003e\n\u003cli class=\"ng-star-inserted\"\u003eBluetooth enabled\u003c\/li\u003e\n\u003cli class=\"ng-star-inserted\"\u003eFor Victron Lith. NG batteries\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003eThe Lynx Smart BMS NG is an exclusive Battery Management System (BMS) specially crafted for the Victron Lithium NG batteries. These batteries utilize Lithium Iron Phosphate (LiFePO4) technology and are offered in 12.8 V, 25.6 V, and 51.2 V versions with different capacities. They can be arranged in series, parallel, and series\/parallel configurations, allowing the formation of battery banks with system voltages of 12V, 24V, or 48V. The maximum number of batteries in a single system is 50, providing a maximum energy storage of 192kWh in a 12V system and up to 384kWh in a 24V and 48V system. For detailed information regarding these batteries, please visit the Victron Lithium NG battery product page. Out of the various BMSes available for the all new Lithium NG batteries, the Lynx Smart BMS NG is the most feature-rich and complete option and integrates seamlessly with other M10 products in the Lynx Distributor system. It is available in 500 A (M10) and 1000 A (M10) versions 1)\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2\u003e\u003cspan\u003eFeatures\u003c\/span\u003e\u003c\/h2\u003e\n\u003cp\u003e\u003cspan\u003e\u003cb\u003eBuilt-in 500 A or 1000 A contactor\u003c\/b\u003e\u003cbr\u003e• Available in 500 A (M10) and 1000 A (M10) versions.\u003cbr\u003e• Acts as a secondary safety system to protect the battery in case primary controls (ATC, ATD and\/or DVCC) fail.\u003cbr\u003e• Suitable as a remote controllable main system switch.\u003cbr\u003e\u003cbr\u003e\u003cb\u003ePre-charge circuit\u003c\/b\u003e\u003cbr\u003e• Prevents high inrush currents when connecting capacitive loads like inverters.\u003cbr\u003e• Eliminates the need for external pre-charging devices.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eMonitoring and control\u003c\/b\u003e\u003cbr\u003e• Bluetooth connectivity for monitoring and control via the VictronConnect App or VE.Can connectivity in combination with GX devices such as the Cerbo GX or Ekrano GX and the VRM portal.\u003cbr\u003e• Readout of cell voltages and temperatures also on GX devices and the VRM portal.\u003cbr\u003e• Built-in battery monitor provides data such as state of charge, voltage, current, historical data, status info and more in real time.\u003cbr\u003e• Diagnostic at a glance with Instant Readout\u003cbr\u003e\u003cbr\u003e\u003cb\u003eDVCC closed loop control as well as ATC\/ATD contacts\u003c\/b\u003e\u003cbr\u003e• Compatible Victron inverter\/chargers, the Orion XS 12\/12-50A DC-DC battery charger and solar charge controllers are automatically controlled via a connected GX device and DVCC.\u003cbr\u003e• ATC\/ATD contacts can be used to control other chargers and loads that have a remote on\/off port.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eProgrammable relay\u003c\/b\u003e\u003cbr\u003e• Can be used either as an alarm relay (combined with the pre-alarm) or to control an alternator via its external regulator (ignition cable).\u003cbr\u003e• Features Alternator ATC mode for safe alternator disconnection before battery disconnects\u003cbr\u003e\u003cbr\u003e\u003cb\u003eAUX terminal\u003c\/b\u003e\u003cbr\u003e• Onboard auxiliary power supply (1.1 A @ system voltage) for powering specific loads (i.e. a GX device) post-BMS shutdown.\u003cbr\u003e• Automatic shutdown of BMS and AUX connection if no charge voltage detected within 5 minutes after a low voltage event\u003cbr\u003e\u003cbr\u003e\u003cb\u003eVE.Can and NMEA 2000 data communication\u003c\/b\u003e\u003cbr\u003e• Easy connection and communication with GX devices via VE.Can using a standard RJ45 network cable.\u003cbr\u003e• Integration into marine networks via NMEA 2000 protocol (requires a VE.Can to NMEA 2000 micro-C male cable).\u003cbr\u003e\u003cbr\u003e\u003cb\u003eLynx Distributor fuse monitoring\u003c\/b\u003e\u003cbr\u003e• Monitor fuse status of up to 4 connected Lynx Distributors via VictronConnect or GX devices.\u003cbr\u003e• Receive alarms in case of blown fuses.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2 class=\"pb-1 pb-md-4 fs-heading-separator\"\u003eSpecifications\u003c\/h2\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003e\n\u003cul\u003e\n\u003cli\u003eBusbar: M10 (Torque: 33 Nm)\u003c\/li\u003e\n\u003cli\u003eContinuous Current Rating: \u003cspan style=\"font-size: 0.875rem;\"\u003e1000A\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eFuse: \u003cspan style=\"font-size: 0.875rem;\"\u003eM10\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eModel: \u003cspan style=\"font-size: 0.875rem;\"\u003eBMS 1000 A NG\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eSize: \u003cspan style=\"font-size: 0.875rem;\"\u003e9.06\"H x 7.09\"W x 3.94\"D\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eVolts: \u003cspan style=\"font-size: 0.875rem;\"\u003e9-60V DC\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eBarcodes: \u003cspan style=\"font-size: 0.875rem;\"\u003e8719076063568, \u003c\/span\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e190760635687\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e\u003cspan\u003e(1044416)\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":51127896768676,"sku":"1044416","price":1178.1,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0423\/0820\/6756\/files\/victron-energy-lynx-smart-bms-1000.webp?v=1757644013"},{"product_id":"victron-energy-lithium-ng-batteries-1048800","title":"VICTRON ENERGY | Lithium NG Batteries (1048800)","description":"\u003ch2\u003eDescription\u003c\/h2\u003e\n\u003cul class=\"fs-list--cleaner\"\u003e\n\u003cli class=\"ng-star-inserted\"\u003eBluetooth Smart\u003c\/li\u003e\n\u003cli class=\"ng-star-inserted\"\u003eSupports 12V,24V \u0026amp; 48V systems\u003c\/li\u003e\n\u003cli class=\"ng-star-inserted\"\u003eRemote on\/off terminals\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003eThe VE.Bus BMS NG serves as a comprehensive Battery Management System (BMS) specifically designed for Victron Lithium NG batteries (it is not compatible with Lithium Battery Smart batteries). This system is intended for use with Victron inverters or inverter\/chargers that utilize VE.Bus communication. It effectively monitors and safeguards the batteries against overvoltage and undervoltage conditions of any individual cell, as well as overtemperature and undertemperature scenarios.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eEquipped with integrated Bluetooth, it establishes a direct connection to all lithium NG batteries within the system, allowing for centralized monitoring through VictronConnect. Additionally, it obtains current and state of charge information directly from the batteries, eliminating the necessity for a separate SmartShunt.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThe lithium NG batteries can be configured in series, parallel, or a combination of both, supporting 12V, 24V, and 48V systems. A maximum of 50 batteries can be used in 12V or 24V banks, and 25 batteries in 48V banks, enabling up to 192 kWh (12V), 384 kWh (24V), and 128 kWh (48V) of storage. Multiple Lynx Smart BMS units can be paralleled to expand capacity and ensure redundancy.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2\u003e\u003cspan\u003eFeatures\u003c\/span\u003e\u003c\/h2\u003e\n\u003cp\u003e• Bluetooth Smart: The VE.Bus BMS NG includes Bluetooth Smart for wireless configuration, monitoring, and firmware updates via the VictronConnect App. Instant Readout shows key data such as SoC, battery temperature, warnings, and alarms directly in the device list, without needing to connect.\u003cbr\u003e• Load disconnect output: Controls the remote on\/off input of a BatteryProtect, inverter, DC-DC converter, or other loads with remote on\/off functionality to prevent deep discharge.\u003cbr\u003e• Charge disconnect output: Controls the remote on\/off port of chargers such as the Smart IP43 Charger, a Cyrix-Li-Charge relay, a Cyrix-Li-ct Battery Combiner, or a BatteryProtect, to prevent overvoltage.\u003cbr\u003e• Pre-alarm output: Provides early warning for low battery voltage before disconnecting loads. Can drive a relay, LED, or buzzer.\u003cbr\u003e• Remote on\/off control: Allows external control of both load and charge disconnect outputs.\u003cbr\u003e• LED indicators: Includes a blue LED for Bluetooth status and a red LED for warnings and errors.\u003c\/p\u003e\n\u003ch2 class=\"pb-1 pb-md-4 fs-heading-separator\"\u003eSpecifications\u003c\/h2\u003e\n\u003cp\u003e\u003cb\u003eMFG #: \u003c\/b\u003e\u003cspan class=\"pl-1\"\u003eBMS300200300\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"pl-1\"\u003e(\u003cspan\u003e1048800)\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":51145532309668,"sku":"1048800","price":156.4,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0423\/0820\/6756\/files\/1_fd35bb48-7c15-40f4-bfbf-9fa4cadf8700.webp?v=1759173407"},{"product_id":"victron-energy-smart-bms-12-200-battery-management-system-1029987","title":"VICTRON ENERGY | Smart BMS 12\/200 Battery Management System (1029987)","description":"\u003ch2\u003eDescription\u003c\/h2\u003e\n\u003cul class=\"fs-list--cleaner\"\u003e\n\u003cli class=\"ng-star-inserted\"\u003eFor 12V Systems\u003c\/li\u003e\n\u003cli class=\"ng-star-inserted\"\u003eBluetooth Enabled\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003eThe Smart BMS 12\/200 is an all-in-one Battery Management system for Victron Lithium-Iron-Phosphate (LiFePO4) Smart Batteries. It has been specifically designed for 12V systems with a 12V alternator such as in vehicles and boats.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eIt combines a Current Limiter, Battery Combiner and Battery Protector in a robust and compact solution and lets you safely connect any size 12V alternator (and starter battery), loads and chargers to Smart Lithium batteries.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThe Smart BMS 12\/200 monitors and protects each individual battery cell within the battery (or battery bank) and will disconnect the alternator, charge sources or DC loads in case of low battery cell voltage, high battery cell voltage or over temperature.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThe dedicated alternator connection provides current limiting and one-way traffic from the alternator into the battery, this so any size alternator (and starter battery) can be safely connected to the Smart Lithium battery (or battery bank) and the starter battery is protected from excessive discharge.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThe BMS is equipped with Bluetooth for monitoring and configuration, a remote on\/off connector, to turn the BMS (and the system) off via a remote switch and a pre-alarm contact, to give a warning signal before the BMS will disconnect the batteries from the system.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2 class=\"pb-1 pb-md-4 fs-heading-separator\"\u003eSpecifications\u003c\/h2\u003e\n\u003cp\u003e\u003cb\u003eMFG #: \u003c\/b\u003e\u003cspan class=\"pl-1\"\u003eBMS210055000\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"pl-1\"\u003e(1029987)\u003c\/span\u003e\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":51145672097956,"sku":"1029987","price":232.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0423\/0820\/6756\/files\/1_446ae3f5-fbaf-4c35-bb58-72d54cb495aa.webp?v=1759196158"},{"product_id":"victron-energy-lynx-smart-bms-1029988","title":"VICTRON ENERGY | Lynx Smart BMS (1029988)","description":"\u003cdiv class=\"col-12\"\u003e\n\u003ch2 class=\"pb-1 pb-lg-4 fs-heading-separator\"\u003eDescription\u003c\/h2\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-9 fsProductOverview__main\"\u003e\n\u003cp\u003e\u003cb\u003eNote: Not for use with Victron Lithium NG batteries, that model is linked below as a related product.\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003eThe Lynx Smart BMS is a dedicated Battery Management System for Victron Lithium Smart Batteries. There are multiple BMS-es available for our Smart Lithium series of batteries, and the Lynx Smart is the most feature rich and complete option.\u003c\/p\u003e\n\u003cul class=\"fs-list--cleaner\"\u003e\n\u003cli class=\"ng-star-inserted\"\u003e500A or 1000A contactor\u003c\/li\u003e\n\u003cli class=\"ng-star-inserted\"\u003eBluetooth enabled\u003c\/li\u003e\n\u003cli class=\"ng-star-inserted\"\u003eM8 or M10 busbar connections\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cp\u003e\u003cspan\u003e• Built-in 500A or 1000A contactor, used as a fall-back safety mechanism and also available as a remote controllable main systems switch\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Battery monitor, indicating state of charge percentage and more data.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Pre-alarm signal: provide a warning before the system shuts down due to -for example- a low cell.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Bluetooth for use with our VictronConnect App, for setup and monitoring.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Local and remote monitoring using a Victron GX device, for example the Cerbo GX.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• The Lynx Smart BMS is part of the modular Lynx Distribution system.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e• Optional M8 or M10 busbar connections\u003c\/span\u003e\u003c\/p\u003e\n\u003cdiv class=\"col-12\"\u003e\n\u003ch2 class=\"pb-1 pb-md-4 fs-heading-separator\"\u003eSpecifications\u003c\/h2\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 fsProductSpecifications__selected-attributes pb-4\"\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cspan\u003e\u003cb\u003eMFG #: \u003c\/b\u003e\u003cspan class=\"pl-1\"\u003eLYN034160200 \u003c\/span\u003e\u003c\/span\u003e|\u003cspan style=\"font-size: 0.875rem;\"\u003e \u003c\/span\u003e\u003cb style=\"font-size: 0.875rem;\"\u003eModel\/Amps: \u003c\/b\u003e\u003cspan class=\"pl-1\" style=\"font-size: 0.875rem;\"\u003eBMS 500 A M8 | \u003cb\u003eSKU:\u003c\/b\u003e 1029988 \u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"fsProductSpecifications__table col-12 col-md-8 pb-3 pb-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"row\"\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eBusbar: M8 (Torque: 14 Nm)\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eFuse: M8\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eModel: BMS 500 A\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eSize: 7.5\"H x 7.1\"W x 3.1\"D\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eVolts: 9-60V DC\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eBarcodes: LYN034160200, 190760474767, 8719076047476\u003c\/div\u003e\n\u003cdiv class=\"fsProductSpecifications__value\"\u003e\n\u003cdiv class=\"col-12 fsProductSpecifications__selected-attributes pb-4\"\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cspan\u003e\u003cb\u003eMFG #: \u003c\/b\u003e\u003cspan class=\"pl-1\"\u003eLYN034170210 \u003c\/span\u003e\u003c\/span\u003e|\u003cspan style=\"font-size: 0.875rem;\"\u003e \u003c\/span\u003e\u003cb style=\"font-size: 0.875rem;\"\u003eModel\/Amps: \u003c\/b\u003e\u003cspan class=\"pl-1\" style=\"font-size: 0.875rem;\"\u003eBMS 1000 A M10 | \u003cb\u003eSKU:\u003c\/b\u003e 1041255 \u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"fsProductSpecifications__table col-12 col-md-8 pb-3 pb-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"row\"\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eBusbar: M10 (Torque: 33 Nm)\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eFuse: M10\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eModel: BMS 1000 A\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eSize: 9.06\"H x 7.09\"W x 3.94\"D\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eVolts: 9-60V DC\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"col-12 col-lg-6 pl-0 pr-md-0 ng-star-inserted\"\u003e\n\u003cdiv class=\"fsProductSpecifications__name\"\u003eBarcodes: LYN034170210, 190760576041\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Victron Energy","offers":[{"title":"BMS 500 A M8","offer_id":51199630901412,"sku":"1029988","price":997.9,"currency_code":"USD","in_stock":true},{"title":"BMS 1000 A M10","offer_id":51199630934180,"sku":"1041255","price":1178.1,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0423\/0820\/6756\/files\/1_549d8aa3-ba7d-452e-95be-8a5933385b3f.webp?v=1765766267"}],"url":"https:\/\/evergreenoffroad.com\/collections\/victron-energy-battery-management-systems.oembed","provider":"Evergreen Offroad","version":"1.0","type":"link"}